· Customer:
Technical Data Sheet
PN: XGS-PB3216AMAG-04 For: IF=20mA
Contents
1.Features 2.Applications
3. Package dimensions 4. Absolute maximum rating
5.Electrical optical characteristics 6.BIN range 7.Package label
8.Soldering pad dimensions 9.Soldering conditions
10. Package tape specifications
11. Typical electro-optical characteristics curves
12.Reliability test items and conditions 13.Cautions 14.Note
Customer confirm Approved by Checked by Issued by
Part No. Emitted Color Chip Material
XGS-PB3216AMAG-04 Amber AlGaInP Green AlGaInP Len'sColor -- Water Clear -- ◆ Features:
Compatible with automatic placement equipment Compatible with reflow solder process
Low power consumption and wide viewing angle
This product doesn’t contain restriction Substance, comply ROHS standard.
◆ Applications:
Automotive and Telecommunication
Flat backlight for LCD ,switch and symbol in telephone and fax General use for indicators
◆ Package Dimensions:
Electrodes: Au Plating
Encapsulating Resin: Epoxy Resin Package: BT Resin
Page 1 of 8
◆ Absolute Maximum Rating （Ta=25℃）
Parameter Power Dissipation Pulse Forward Current DC Forward Current Reverse Voltage Operating Temperature Range Storage Temperature Range
Symbol PM IFP IF VR Topr Tstg Value AM 80 30 20 5 -40~+80 -40～+85 AG 80 Unit Mw mA mA V ℃ ℃ IFP condition: pulse width ≤1ms ,duty cycle ≤1/10
◆ Electrical Optical Characteristics（Ta=25℃）
Parameter Symbol Min 80 20 1.8 1.8 -- -- 600 565 -- -- ±10% Amber Green Amber Green Amber Green Amber Green Amber Typ. 160 50 2.0 2.0 -- -- 605 570 120 120 Max. -- -- 2.4 2.4 10 10 -- -- -- -- mcd Unit Test Condition Luminous Intensity IV IF =20mA Forward Voltage VF V IF =20mA Reverse Current IR uA VR=5V Dominant Wavelength λd nm IF=20mA 2θ1/2 Viewing Angle Green Notes: 1.Tolerance of Luminous Intensity Deg. IF =20mA 2.Tolerance of Dominant Wavelength ±2nm
3. Tolerance of Forward Voltage ±0.05V
4. Luminous Intensity is measured by XGS’s equipment on bare chips
Page 2 of 8
◆ Soldering Pad Dimensions:
◆ Soldering Conditions
Reflow soldering profile
Time 3℃/sec. Temperature 210℃ (Maximum allowable soldering conditions) 260℃Max. 10sec.Max. Pre-heating 120~160℃ 3℃/sec. 120se.c.Max. -4℃/sec. 60~120sec. • Reflow soldering should not be done more than two times. • Do not stress its resin while soldering. • After soldering,do not warp the circuit board. Page 3 of 8 ◆ Package Tape Specifications: (4000 pcs/Reel) Feeding,Direction Dimensions of Reel ( Unit:mm) Feeding Direction Dimensions of Tape (Unit:mm) A 2 1 4 3 A Arrangement of Tape(Unit:mm) Page 4 of 8 ◆ Typical Electro-Optical Characteristics Curves： Relative Luminous Intensity Vs.Wavelenght Relative Luminous Intensity (%) 100 Ta=25°C Forward Current Vs.Forward Voltage Ta=25°C 50 AG 1.5 3.5 Forward Current (mA) A M 75 40 30 20 10 AM AG 50 2.0 2.5 3.0 25 0 540 560 580 600 620 0 1.0 Wavelenght(nm) Forward Voltage(V) Page 5 of 8 ◆ Reliability (1) Test Items and Conditions NO 1 2 3 4 Test Item Temperature Cycle High Temperature Storage High Temperature And High Humidity Working Low Temperature Storage Test Conditions -40±5℃→25±5℃→100±5℃→25±5℃ (30min，5min，30min，5min) 100 Cycles Ta：100±5℃ Test time=1000HRS(-24HRS,+72HRS) Ta：85±5℃，RH:85±5%，IF=20 Test time=500HRS(-24HRS,+72HRS) Ta：-40±5℃ Test time=1000HRS(-24HRS,+72HRS) Connect with a power IF=20mA Ta=Under room temperature Test time=1000HRS(-24HRS,+72HRS) Sample 20 20 20 20 Ac/ Re 0/1 0/1 0/1 0/1 5 6 Operating Life Test Thermal Shock 20 20 0/1 0/1 7 IR-Reflow Pb-Free Process -40±5℃→100±5℃ (15min，15min) 100 Cycles ① 80℃②100℃③120℃④ 160℃⑤170 ℃⑥235℃⑦270℃⑧255℃， 60cm/min，2 times 20 0/1 (2) Criteria of judging the damage Item Forward voltage Reverse current Luminous intensity Symbol VF IR IV Test condition IF=Test Current VR=5V IF=Test Current Criteria for judgement Min. / / L.S.L*0.7 / Max. U.S.L*1.1 15uA / U.S.L±2nm Wave length Appearance λD/λP / IF=Test Current View check L.S.L: Lower standard level No mechanical damage * U.S.L: Upper standard level Page 6 of 8 ◆ Cautions 1、Package When moisture is absorbed into the package it may vaporize and expand during soldering. There is a possibility that this can cause exfoliation of the contacts and damage to the optical characteristics of the LEDs. So the moisture proof package is used to keep moisture to a minimum in the package. 2、Storage Before opening the package: The LEDs should be kept at 5~30°C and 60%RH or less. The LEDs should be used within a year. After opening the package: The LED must be used within 24 hours, else should be kept at 5~30℃ and 30% RH or less. The LEDs should be used within 7days after opening the package. If unused LEDs remain, they should be stored in moisture proof packages, recommended to return the LEDs to the original moisture proof bag and to reseal the moisture proof bag again. If the LEDs have exceeded the storage time, baking treatment should be performed more than 24hours at 60±5°C. 3、Soldering Iron Each terminal is to the tip of soldering iron temperature less than 300℃ for 3 seconds within once in less than the soldering iron capacity 25 W.Leave two seconds and more internals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 4、Repairing Repairing should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. 5、The LED electrode sections are comprised of a gold plated. The gold surface may be affected by environments which contain corrosive gases and so on. Please avoid conditions which may cause the LED to corrode or discolor. This corrosion or discoloration may cause difficulty during soldering operations. It is recommended that the User use the LEDs as soon as possible. 6、Please avoid rapid transitions in ambient temperature, especially in high humidity environments where condensation can occur. Page 7 of 8 ◆Notes: 1、Above specification may be changed without notice. We will reserve authority on material change for above specification. 2 、 When using this product, please observe the absolute maximum ratings and the instructions for the specification sheets. We assume no responsibility for any damage resulting from use of the product which does not comply with the instructions included in the specification sheets. Page 8 of 8 因篇幅问题不能全部显示，请点此查看更多更全内容